OS: Windows 11 64-bit, Transceiver: ICOM IC-7300, Tuner: MFJ IntelliTuner MFJ-998
After installing, only RX works in Decodium with TX only occurring for a fraction of a second before transmitting nothing for the rest of the 3 seconds in both FT2 and FT8 (FT8 being 15 seconds, of course, but same issue). I can tell nothing is being transmitted as the needle on the tuner doesn't move and there is only a small flash of a signal sometimes on the transceiver screen.
In a separate, untouched install of WSTJ-Z both RX and TX work fine. Between the two programs the settings are identical (default data bits, default stop bits, default handshake, CAT PTT, data/pkt mode, faked split operation) with the frequency set at 28.184MHz in FT2. Restarting Windows or any other hardware did not fix anything. Audio is set up correctly as well (USB Audio CODEC). The tune button in the program transmits normally and continues transmitting as well.
Only RX possible in Decodium, empty transmission in TX
💬 Risposte (20)
#1
I get the same issue, did you resolve it?
#2
I got the same thing happening as well. What I did find was, when responding to a CQ radio would TX for a second then wait for what I can tell is the next segment to check if the CQ is still present. Then the software will let the radio TX a signal. If the CQ is not present the radio will TX an empty signal.
I am running Decodium in a stand alone directory. I still haven't got JTALERT to work with it.
I am running Decodium in a stand alone directory. I still haven't got JTALERT to work with it.
#3
The same problem
#4
new instalation here and ft2 onl tx in 1st session and then it ptt but no audio stream
everthing else work but ft2 does not send an audio strem to usb port
icom 7100
seems problem is sending to usb port on ft2 software side
everthing else work but ft2 does not send an audio strem to usb port
icom 7100
seems problem is sending to usb port on ft2 software side
#5
the same problem here, with ICOM IC-7600
#6
Same problem here. Tested it on the IC7300 and the FTdx10. During the first transmission LF is generated and send to the radio. After that there is no audio transmission anymore.
WSJT-X 2.7 and 3.0RC1 are running fine though.
WSJT-X 2.7 and 3.0RC1 are running fine though.
#7
I noticed that it might depend on the NTP flag being enabled if a slightly high deviation in time accuracy is detected. To resolve the issue where no audio signal was generated from the second cycle onward, I disabled the NTP flag.
#8
Alberto's trick works for me! Grazie Alberto
#9
73 Alberto, disabling the NTP flag worked for me as well
#10
Yes, the new version works fine now. Thanks for your good work!
#11
provate a togliere la spunta da SERVER NTP
#12
How do you disable NTP Flag ?
#13
The same problem with Kenwood TS-2000, Decodium_3.0_2402261730_FT2_x64, Windows 10 x64 when NTP enabled.
#14
CHEERS TNX
Alberto, disabling the NTP flag worked for me as well
well seem all good on the tx side for now in windows
the linux side seems to be ok
Alberto, disabling the NTP flag worked for me as well
well seem all good on the tx side for now in windows
the linux side seems to be ok
#15
Gd evening, can anybody explain where to disable NTP flagP ?
I guess there is conflict with UDP port 123 but I'm not able to fix it.
Any help will be greatly appreciated... thanks
Max
I guess there is conflict with UDP port 123 but I'm not able to fix it.
Any help will be greatly appreciated... thanks
Max
#16
Unchecking the NTP did it for me. Hmmmmm.
#17
The same, now i try to disable NTP, but the same Issue is on the original Version of WSJTX, JTDX works fine.. mabe helpful for resolve the Problem. i Think its a Problem with USB-Audio.
Please setup a englisch Forum please, not many Peaople arount the World speak Italian as nativ :) but want to use your Programm.
Please setup a englisch Forum please, not many Peaople arount the World speak Italian as nativ :) but want to use your Programm.
#18
Edit: MacOS 15.x Decodium 1.5.3
#19
Installed 1.6.0 no ptt no tx, rx fine using same settings as Decodium 3.
Decodium 3 still works fine. M0PAW
Decodium 3 still works fine. M0PAW
#20
I have the Same Problem I have a Yaesu FT-710Aess and nothing transmits at all, watching the power meter it never moves, but when I key up my Mic power meter moves.